Competitors List for JOHN CRANE® Seals
Welcome to Vulcan's Unique Seal Identification (ID) Suite providing you, the user, a view of our complete range of seals, with the capability to identify seals and their characteristics as well as conversions from our competitor product codes.
Competitors List for JOHN CRANE® Seals
 |
 |
Multiple Spring seal with a highly effective design, commonly used in chemical and petrol-chemical duties. These seals are supplied with the Type 25 seat (shown). Standard Type 1609 incorporates a PTFE Wedge secondary seal or alternatively can be supplied with an O-Ring (See 1645S for design) |
 |
 |
O-Ring mounted stationary seat to DIN 24960 (EN12756) Standard with short tail. The seat offers different axial dimensions to the Type 8 DIN short seat and can be utilised with most seals particularly the Type 24 and 1724 designs. |
 |
 |
O-Ring mounted stationary seat to DIN 24960 (EN12756) Standard with long tail and drive slot. The seat offers different axial dimensions to the Type 8 DIN long seat and can be utilised with most seals particularly the Type 24 and 1724 designs. |
 |
 |
DIN 24960 non-pinned short seat, designed to readily puch fit. Seat is fitted with an elastomer O-Ring, and the face is profiled to accept a restraining bezel plate. |
 |
 |
DIN 24960 pinned seat designed to readily push fit, with a rectangular section seat ring in P.T.F.E. Pin diameter recommended is 3mm up to size 35mm and 4mm from 38mm to 100mm. Face profiled to accept a restraining bezel plate. |
 |
 |
Vulcan produce a simple, 1.0 shaft size rubber encased single-spring seal for use in several common food and dairy equipment applications. |
 |
 |
Vulcan Type 1644 rubber-encased multi-spring seal, for use in the food, beverage and dairy industries applications. Available with Ni-Resist seal face and carbon seat-ring, Nitrile elastomers, other material combinations available to special order. |
 |
 |
Coolant pump seal primarily utilised in combustion engine water pumps, with dimensions to equate to the common American seal standard. |
 |
 |
Coolant pump seal primarily utilised in combustion engine water pumps. The clearance of the seal and seat above the shaft allows one size to be used on several shaft diameters. Type 75 has dimensions to equate to the common American seal standard.Pricing shown is for materials highlighted below; |
 |
 |
Sleeve mounted, rubber bellows seal, with dimensions to equate to the common American seal standard. Mass produced and easily fitted for low pressure, general applications on small shaft diameters. |
 |
 |
Sleeve mounted, rubber bellows seal, Type 65 with dimensions to equate to the common American seal standard. Mass produced and easily fitted for low pressure, general applications on small shaft diameters. |
 |
 |
Wave spring mechanical seal with thin cross section and short working length. Most commonly used on rotary lobe pumps, found extensively in the food, process, dairy and brewery industries. Popular, common sizes are fitted with Vulcan’s Sinusoidal Split Wave-Springs. |
 |
 |
Rotary based, bi-directional, wave-spring seal to suit standard rotary lobe SSP® pumps. The Type 1682 is driven directly from the grub-screws. Most commonly found in the food, brewing and dairy industries. |
 |
 |
Narrow profile, multiple spring seal with a highly efficient design, frequently specified in chemical process industry pumps. Use Type 1659 with a PTFE Wedge or Type 1659S for O-Ring variant. Commonly fitted with Vulcan Type 24 DIN Long or Type 24 DIN Short Stats. |
 |
 |
Multiple-Spring, stepped shaft, balanced seal with a highly efficient design. Standard Type 1659B incorporates a PTFE Wedge shaft seal, or specify Type 1659BS for the Balanced O-Ring version. Supplied with a suitable smaller shaft size Type 24 DIN Long (as shown). |
 |
 |
Multiple-Spring, stepped shaft, balanced seal with a highly efficient design. Standard Type 1659B incorporates a PTFE Wedge shaft seal, or specify Type 1659BS for the Balanced O-Ring version. Supplied with a suitable smaller shaft size Type 24 DIN Long (as shown). |
 |
 |
Narrow profile, multiple spring seal with a highly efficient design, frequently specified in chemical process industry pumps. Use Type 1659 with a PTFE Wedge or Type 1659S for O-Ring variant. Commonly fitted with Vulcan Type 24 DIN Long or Type 24 DIN Short Stats. |
 |
 |
Multiple-Spring, stepped shaft, balanced seal to common American Installation dimensions. Standard Type 1645B incorporates a PTFE Wedge secondary seal with Type 1645BS being the O-Ring variant. Commonly fitted with the next shaft size down Type 25 seat. |
 |
 |
Multiple-Spring, stepped shaft, balanced seal to common American Installation dimensions. Standard Type 1645B incorporates a PTFE Wedge secondary seal with Type 1645BS being the O-Ring variant. Commonly fitted with the next shaft size down Type 25 seat. |
 |
 |
Multiple-Spring, stepped shaft, balanced seal to common American Installation dimensions. Standard Type 1645B incorporates a PTFE Wedge secondary seal with Type 1645BS being the O-Ring variant. Commonly fitted with the next shaft size down Type 25 seat. |
 |
 |
Narrow profile, multiple-spring seal, designed for common American installation dimensions, in chemical process industry equipment. Complies with ANSI B73-1974 centrifugal pump standard. Standard Type 1645 utilises a PTFE Wedge secondary seal and Type 1645S uses an O-Ring. Supplied with a Type 25 V seat. (as shown) |
 |
 |
Multiple Spring, stepped shaft, balanced seal, alternative to the Type 1609/1609S. Standard Type 1609B utilises a PTFE wedge seal, or specify Type 1609BS for the O-Ring version. Commonly fitted with the next shaft size down Type 25 seat. |
 |
 |
Multiple Spring, stepped shaft, balanced seal, alternative to the Type 1609/1609S. Standard Type 1609B utilises a PTFE wedge seal, or specify Type 1609BS for the O-Ring version. Commonly fitted with the next shaft size down Type 25 seat. |
 |
 |
Multiple Spring seal with a highly effective design, commonly used in chemical and petrol-chemical duties. These seals are supplied with the Type 25 seat (shown). Standard Type 1609 incorporates a PTFE Wedge secondary seal or alternatively can be supplied with an ‘O’-Ring (See 1645S for design). |
 |
 |
Robust, short working length highly accommodating and reliable rubber diaphragm balanced seal, which provides enhanced seal capability, performance and life. Improved design features further enhance this popular seal. Suitable for common US standard housing and working length dimensions. |
 |
 |
Robust, short working length highly accommodating and reliable rubber diaphragm balanced seal, which provides enhanced seal capability, performance and life. Improved design features further enhance this popular seal. Suitable for common US standard housing and working length dimensions. |
 |
 |
Metric and imperial, robust, short working length highly accommodating and reliable, rubber diaphragm balanced seal which provides enhanced seal capability, performance and life. Improved design features further enhance this popular seal. Suitable for common UK and Euro housing and working length dimensions, but also available to suit common US housing dimensions (Type A4) |
 |
 |
Robust, long working length, highly accommodating and reliable, rubber diaphragm balanced seal, which provides enhanced seal capability, performance and life. Improved design features enhance this popular seal. Suitable for common UK and Euro housing dimensions. |
 |
 |
Compact single spring, rubber diaphragm seal specifically designed to comply with DIN 24960 (EN12756) housings.Shown with boot mounted seat, but is also often specified with a Type 24 O-Ring mounted DIN Long or Short seat (Types 24L or 24S respectively) |
 |
 |
Metric and imperial single spring, rubber diaphragm shaft seal (Imperial shown), designed for different sized seat housings and seal working lengths to the Types 10 + 20. Imperial sizes are most commonly found on American equipment. Alternative version with longer working length available. |
 |
 |
Universal compact DIN seal and seat available with different DIN standard working lengths. This robust, heavy duty bellows design provides excellent flexibility and durability. The seal is supplied as standard with a boot mounted seat, however alternate O-ring mounted seats are available. |
 |
 |
Universal compact DIN seal and seat available with different DIN standard working lengths. This robust, heavy duty bellows design provides excellent flexibility and durability. The seal is supplied as standard with a boot mounted seat, however alternate O-ring mounted seats are available. |
 |
 |
Universal compact DIN seal and seat available with different DIN standard working lengths. This robust, heavy duty bellows design provides excellent flexibility and durability. The seal is supplied as standard with a boot mounted seat, however alternate O-ring mounted seats are available. |
